Daikin FTXG35CVMBS Dokumentacja Pobierz pdf (Strona 150)

Si04-402 Indoor Unit

Removal Procedure 141

Pull out the limit switch.

Disconnect the

terminals from the

board.



Pb free soldering is adopted

for PCB.

When replacing PCB, use

the particular solder and

iron.

Black······(1)

White······(2)

Red

········(3)

Cut the clamps.



Clamps should be used all

the time.

Fix it as it was before.

Disconnect the

connector for the signal

receiver PCB (S46).

Step

Procedure Points

1 2 ... 145 146 147 148 149 150 151 152 153 154 155 ... 193 194

Inverter Pair 1
Indoor Unit 2
Outdoor Unit 2
Table of Contents iii 4
1. Introduction 6
1.1.3 Inspection after Repair 8
1.1.4 Using Icons 9
1.1.5 Using Icons List 9
Si04-402 10
List of Functions 1 10
1. List of Functions 11
Specifications 3 12
1. Specifications 13
230V, 50Hz 14
1.1 Indoor Unit 17
PCB(2): Signal Receiver PCB 18
1.2 Outdoor Unit 19
PCB(2): Filter PCB 20
Function and Control 13 22
1. Main Functions 23
Si04-402 Main Functions 26
Function and Control 17 26
(R4085) (R4085) 27
1.5 Programme Dry Function 28
1.6 Automatic Operation 29
1.7 NIGHT SET Mode 30
1.8 INTELLIGENT EYE 31
TPF=(20min.) 32
ON / OFF button 33
2. Function of Thermistor 34
3. Control Specification 35
3.2 Frequency Control 36
3.3.1 Preheating Operation 37
3.3.4 3-minutes Standby 38
3.4 Discharge Pipe Control 39
3.5 Input Current Control 39
3.7 Heating Peak-cut Control 40
3.8 Fan Control 41
3.10 Defrost Control 42
34 Function and Control 43
Function and Control 35 44
36 Function and Control 45
3.12 Malfunctions 46
3.13 Forced Operation Mode 47
3.14 Additional Function 47
System Configuration 39 48
1. System Configuration 49
2. Instruction 50
Installation site 51
Electrical work 51
System relocation 51
2.2 Names of Parts 52
Remote Controller 54
To set the batteries 55
ATTENTION 56
To set the clock 57
Si04-402 Instruction 58
System Configuration 49 58
Instruction Si04-402 59
50 System Configuration 59
System Configuration 51 60
〈HEAT〉 The flap will go down 61
2.6 POWERFUL Operation 62
1. Press “SILENT button” 63
2.8 INTELLIGENT EYE Operation 64
Notes on “INTELLIGENT EYE” 65
2.9 TIMER Operation 66
2.10 Care and Cleaning 68
[ Maintenance ] 69
[ Replacement] 69
Before a long idle period 70
2.11 Troubleshooting 71
Check again 72
Case Check 72
Disposal requirements 73
C:3P119293-1 73
Service Diagnosis 65 74
1. Caution for Diagnosis 75
3. Service Check Function 77
Service Diagnosis 69 78
70 Service Diagnosis 79
4. Troubleshooting 80
72 Service Diagnosis 81
Model Type Connector No 81
Service Diagnosis 73 82
Service Diagnosis 75 84
Check No.01 85
Service Diagnosis 77 86
78 Service Diagnosis 87
Service Diagnosis 79 88
Wired Remote Controller ) 89
Service Diagnosis 81 90
82 Service Diagnosis 91
Service Diagnosis 83 92
4.12 Compressor Lock 93
4.13 DC Fan Lock 94
86 Service Diagnosis 95
Service Diagnosis 87 96
88 Service Diagnosis 97
Service Diagnosis 89 98
90 Service Diagnosis 99
Si04-402 Troubleshooting 100
Service Diagnosis 91 100
Troubleshooting Si04-402 101
92 Service Diagnosis 101
Service Diagnosis 93 102
94 Service Diagnosis 103
J3, J6, H9 104
96 Service Diagnosis 105
Service Diagnosis 97 106
98 Service Diagnosis 107
4.23 Insufficient Gas 108
Troubleshooting 109
Check No.4 109
Refer to P.102 109
Check No.6 109
Refer to P.104 109
4.24 Over-voltage Detection 110
5. Check 111
Check No.5 112
Check No.7 114
Check No.8 115
Check No.9 115
5.1.10 Power Transistor Check 117
Removal Procedure 109 118
1. Indoor Unit 119
Grille side 121
Decorative 121
(R3769)(R3768) 121
Decorative plate 122
Indoor Unit Si04-402 125
116 Removal Procedure 125
Procedure Points 125
Si04-402 Indoor Unit 128
Removal Procedure 119 128
1.4 Removal of Lamp Cover 131
(R3816) (R3813) (R3814) 132
124 Removal Procedure 133
Removal Procedure 125 134
1.7 Removal of Outlet Grille 136
128 Removal Procedure 137
Removal Procedure 131 140
1.9 Removal of Electrical Box 141
Removal Procedure 137 146
1.10 Removal of PCB 147
Loosen the screws of 148
Release the front hook 148
Layout of the wiring 149
Loosen the screw and 149
Removal Procedure 145 154
3. Remove the bearing 157
Lift up the right part of 157
Removal Procedure 149 158
2. Outdoor Unit 159
Lead wire Propeller fan 162
Outdoor Unit Si04-402 163
154 Removal Procedure 163
When reassembling, make 165
2.2 Removal of Electrical Box 166
Si04-402 Outdoor Unit 168
Removal Procedure 159 168
160 Removal Procedure 169
2.4 Removal of Sound Blanket 170
162 Removal Procedure 171
2.5 Removal of Four Way Valve 172
164 Removal Procedure 173
2.6 Removal of Compressor 174
Heat up the brazed part 175
Lift the compressor up 175
2.7 Removal of PCB 176
Loosen the 4 screws 177
Undo the 3 hooks on 177
Lift and pull out the 177
Removal Procedure 169 178
170 Removal Procedure 179
Others 171 180
1. Others 181
(R2871) (R2872) 182
Others Si04-402 183
174 Others 183
Appendix 175 184
1. Piping Diagrams 185
2. Wiring Diagrams 186
Wiring Diagrams Si04-402 187
178 Appendix 187
IndexIndex 188
Index iii 190
Drawings & Flow Charts 192

Komentarze do niniejszej Instrukcji

Brak uwag

Daikin FTXG35CVMBS Dokumentacja Strona 150

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Klimatyzatory typu split Daikin FTXG35CVMBS